Developing a Biodegradable Film for Packaging with Lignocellulosic Materials from the Amazonian Biodiversity.

The development of packaging films made from renewable raw materials, which cause low environmental impact, has gained attention due to their attractive properties, which have become an exciting option for synthetic films. In this study, cellulose micro/nanofibrils (MFC/NFC) films were produced with forest residues from the Amazon region and evaluated for their potential to generate alternative packaging to traditional plastic packaging. The MFC/NFC were obtained by mechanical fibrillation from fibers of açaí seeds (Euterpe oleracea), titica vine (Heteropsis flexuosa), and commercial pulps of Eucalyptus sp. for comparison. The fibrillation of the titica vine culminated in higher energy expenditure on raw materials. The açaí films showed a higher tensile strength (97.2 MPa) compared to the titica films (46.2 MPa), which also showed a higher permeability rate (637.3 g day-1 m-2). Films of all raw materials scored the highest in the grease resistance test (n° 12). The films produced in the study showed potential for use in packaging for light and low moisture products due to their adequate physical, mechanical, and barrier characteristics. New types of pre-treatments or fibrillation methods ecologically correct and viable for reducing energy consumption must be developed, mainly for a greater success of titica vine fibrillation at the nanoscale.

Effect of different pre-treatments on the redispersion capacity of spray-dried microfibrillated cellulose: Elaboration and characterization of biofilms.

This study aimed to evaluate the influence of the addition of the cationic surfactant cetyltrimethylammonium bromide (CTAB) in microfibrillated cellulose (MFC/CNFs) suspensions submitted to different pretreatments to produce redispersible spray-dried (SD) MFC/CNFs. Suspensions pretreated with 5 % and 10 % sodium silicate and oxidized with 2,2,6,6,-tetramethylpiperidinyl-1-oxyl (TEMPO) were modified with CTAB surfactant and subsequently dried by SD. The SD-MFC/CNFs aggregates were redispersed by ultrasound to produce cellulosic films by the casting method. In summary, the results demonstrated that the addition of CTAB surfactant to the TEMPO-oxidized suspension was critical to achieving the most effective redispersion. The experimental results obtained using micrographs, optical (UV-Vis), mechanical, water vapor barrier properties, and the quality index confirmed that the addition of CTAB to the TEMPO-oxidized suspension favored the redispersion of spray-dried aggregates, development of cellulosic films with attractive properties, offering possibilities for the elaboration of new products, for example, in the production of bionanocomposites with higher mechanical performance. This research brings interesting insights into the redispersion and application of SD-MFC/CNFs aggregates, strengthening the commercialization of MFC/CNFs for industrial use.

Current practices of conducting forest management plans in the Amazon may risk the survival of timber species.

Measurement of the recovery of wood stocks in logging areas in the Amazon helps to understand the efficiency of policies for the use and conservation of native forests. This work evaluated the effects of logging on the dynamics and production of commercial species in the short and medium term in a conservation unit in the state of Rondônia. Structural patterns of the species as a function of mortality and recruitment rates, patterns of average increment in diameter, and estimates of forest production in the short and medium term were analyzed. The study was carried out in an area designated as Annual Production Unit 2 of Forest Management Unit III of Jamari National Forest. In addition to legalized harvesting, there are reports of illegal logging in the area as of 2015. Inventory data from 2011, 2015, and 2018 were used, considering trees of commercial value with a diameter at breast height (DBH) greater than 10 cm. Mortality rate, recruitment, periodic annual increment, absolute tree density, basal area, and commercial volume, by species and DBH classes, as well as the similarity of the species regarding the growth pattern. The population structure of species over the years was affected by tree mortality, mainly due to damage caused by illegal logging. Mean increment values varied by species and diameter classes, and six species represented 72% of the total volume of wood stock. It is important to review the criteria for sustainable forest production in the long term. Thus, it is necessary to promote species diversity and improve public authorities' capacity to enforce and of the private sector to comply with legislation. This, in turn, will enable the development of strategies to make the consumption of legal wood more rational.

Mandacaru cactus as a source of nanofibrillated cellulose for nanopaper production.

In this work, nanofibrillated cellulose (NFC) was extracted from cactus Cereus jamacaru DC. (mandacaru) for nanopaper production. The technique adopted includes alkaline treatment, bleaching, and grinding treatment. The NFC was characterized according to its properties and scored based on a quality index. Particle homogeneity, turbidity, and microstructure of the suspensions were evaluated. Correspondingly, the optical and physical-mechanical properties of the nanopapers were investigated. The chemical constituents of the material were analyzed. The sedimentation test and the zeta potential analyzed the stability of the NFC suspension. The morphological investigation was performed using environmental scanning electron microscopy (ESEM) and transmission electron microscopy (TEM). X-ray diffraction (XRD) analysis revealed that Mandacaru NFC has high crystallinity. Thermogravimetric analysis (TGA) and mechanical analysis were also used and revealed good thermal stability and good mechanical properties of the material. Therefore, the application of mandacaru is interesting in sectors such as packaging and electronic device development, as well as in composite materials. Given its score of 72 points on a quality index, this material was presented as an attractive, facile, and innovative source for obtaining NFC.

Eco-friendly particleboard production from coconut waste valorization.

Reusing agro-industrial waste does not only help to mitigate environmental impact but also enables valorization through the development of new products. The aim is to enhance the physical and mechanical properties of particleboard panels produced with Eucalyptus wood and different proportions of waste products-coconut fiber (Cocos nucifera L.). Physical properties (density, water absorption, and thickness swelling) and mechanical properties (static bending and internal bond resistance) were assessed, and panels reinforced with coconut fiber showed the best qualities with higher density, greater dimensional stability, and less water absorption. Static bending resistance and internal bond resistance also increased significantly. This demonstrated the potential of achieving compatible characteristics for civil construction and furniture production through the inclusion of waste material. The impact of this research is obtained from the utilization of an important agro-industrial residue in the manufacture of permanent composites.

Propriedades físico-mecânicas da madeira de freijó, Cordia goeldiana (Boraginacea), produzida em sistema agroflorestal multiestratificado no sudoeste da Amazôni / Physico-mechanical properties of the wood of freijó, Cordia goeldiana (Boraginacea), produced in a multi-stratified agroforestry system in the southwestern Amazon

Os sistemas agroflorestais (SAFs) integram, com práticas sustentáveis, culturas agrícolas e florestais para produção de madeira e alimentos, conservando os serviços ambientais e a biodiversidade. O freijó, Cordia goeldiana, tem potencial para cultivo na Amazônia para fins madeireiros, porém dados sobre as características de sua madeira em SAFs são escassas. Objetivou-se determinar as propriedades físico-mecânicas e aplicações tecnológicas da madeira de freijó produzida em um SAF multiestratificado estabelecido no estado de Rondônia, Brasil em 1996. No SAF, as espécies agrícolas e madeireiras foram estabelecidas em renques duplos no espaçamento 5,0 m x 2,5 m. Abateram-se três árvores de freijó com 19 anos de idade, para caracterização química, física (densidade e estabilidade dimensional) e mecânica (compressão, flexão estática, dureza Janka e cisalhamento) da madeira. A madeira de freijó apresentou composição química similar à de madeiras nobres tropicais, peso moderado (582,63 kg m-3) e estabilidade dimensional elevada em comparação com outras madeiras consagradas no mercado (retração longitudinal, radial e tangencial = 0,25, 4,27 e 6,83%, respectivamente). Os valores de resistência à compressão paralela (32,32 MPa) e perpendicular (8.02 MPa), resistência específica (55,32 MPa kg-1 m-3), dureza Janka paralela (2373,33 N) e perpendicular (2326,67 N), resistência à flexão estática (63,5 MPa) e ao cisalhamento (5,94 MPa) foram semelhantes aos valores observados em outras madeiras tropicais de alta densidade, produzidas em monocultivo e florestas naturais. A madeira em estudo é adequada para fabricação de produtos de alto valor agregado, como móveis finos, pisos residenciais, instrumentos musicais e peças estruturais. (AU)